1. The main products of nickel electrolysis Brand Ni9999 Ni9996 Ni9990 Ni9950 Ni9920 Chemical The total amount of nickel and cobalt, not less than 99.99 99.96 99.9 99.5 99.2 learn Cobalt, not big 0.005 0.02 0.08 0.15 0.1 to make miscellaneous C 0.005 0.01 0.01 0.02 0.5 Minute quality Si 0.001 0.002 0.002 - - (%) Contain P 0.001 0.001 0.001 0.003 0.02 　 the amount, S 0.001 0.001 0.001 0.003 0.02 　 Do not Fe 0.002 0.01 0.02 0.2 0.5 　 Big Cu 0.0015 0.01 0.02 0.04 0.15 　 in Zn 0.001 0.0015 0.002 0.005 - 　 　 As 0.0008 0.0008 0.001 0.002 - 　 　 Cd 0.0003 0.0003 0.0008 0.002 - 　 　 Sn 0.0003 0.0003 0.0008 0.0025 - 　 　 Sb 0.0003 0.0003 0.0008 0.0025 - 　 　 Pb 0.0003 0.001 0.001 0.002 0.005 　 　 Bi 0.0003 0.0003 0.0008 0.0025 - 　 　 Al 0.001 - - - - 　 　 Mn 0.001 - - - - 　 　 Mg 0.001 0.001 0.002 - - Surface quality of electrolytic nickel: 1. Each grade of electrolytic nickel should be cleaned on the surface and the electrolyte in the interlayer, the surface is clean, and there is no contamination of the oil. Note: The Ni9920 grade can be an amorphous electrolytic nickel product. 2. Ni9999, Ni9996, Ni9990 brand electrolytic nickel should be subject to the following provisions: ( 1 ) The average thickness of electrolytic nickel should not be less than ( 2 ) The edges of the electrolysis shall not have dendritic agglomeration and dense pores (allowing for trimming). ( 3 ) The surface of electrolytic nickel shall not have a diameter greater than ( 4 ) The surface height of electrolytic nickel is greater than Note: Table 2 Examples of anode mud rate and chemical composition (%) of nickel sulfide electrolysis factory S Ni Cu Co Anode mud rate /% I factory 75～80 4 0.7 0.08 30 II factory 80 4~6 0.4 to 1 　 25~27 III factory ~70 2 to 3 0.25 0.02~0.03 25~30
Flexible lift gate is a flexibel soft curtain door, inside and outside the two curtains , curtains used between the aluminum beams connected with a vertically movable rail , the roof beams have levels not in the same straight line and hanger large plants in particular Be applicable , Flexible lift door installation does not take up interior space in the hole inside , When the first move to open the door , and finally superimposed over the hole , Off event curtain rail first and then fall down until its is completely closed
Door body composition :
The bottom of the door curtain rail aluminum beam beam seal top drive system and transmission of electrical control systems and safety devices
Flexible door features:
1. Light weight compared with other types of the same size door , flexible door lighter weight reduces the strength of steel at the top of the doorway architecture degree requirements ,
2. Small compared with the same specification of the machine style doors 2, footprint ,flexible installation in the door after the hole is turned on internally stacked above the hole , do not take up interior space , Large Span hole may be provided a plurality of movable rail the entire door into several independent stacking doors shorten the span of a single door so that the overall thickness of the door is reduced , further reducing the footprint
3. Rational layout flexible doors with movable rail rail can set different activities based on the specific circumstances of the door into the door several sizes of uneven accumulation of doors to make the building as a whole rational layout greatly reduces the overall architecture of the space and cost
4. The wind strength between two layers of high flexible door curtain as the bottom of an aluminum beam has a wind skeleton steel structure , By adjusting the beam thickness and spacing , which can resist wind pressure of any intensity , so the door can be flexible for use in any area
5. The tensile strength of the flexible door after door curtain is double polyester fabric , high tensile wire rope equipped with ultra-high hole suitable for large machinery such as aircraft hangars and repository
6. The curtain coated with vinyl coated with a waterproof sunscreen and smoldering performance , capable of sound absorption retardant insulation mildew proof and so on
7. Safe door , Cube with anti-lock break to ensure safety in case of accidental breakage of wire rope jammed in the door quickly experience anywhere rails , Multiple protection features mechanical and electrical installation to ensure t he safety of goods passing aircraft and other vehicles and personnel , the movable rail is also equipped with anti-fall device , you can ensure reliable parked at the top of the hole after the movable rail is raised without falling , The bottom of the door is equipped with and airbag , it will immediately rebound to rise until the safety door drops open when obstacles encountered in the process , You can also install infrared protection device on the door
PVC flexible gate,pvc high speed gate door, pvc high speed rolling gate door, flexible rolling doors,fast doors SHENZHEN HONGFA AUTOMATIC DOOR CO., LTD , https://www.hongfarrud.com
1) Electrolytic Nickel The ultimate goal of electrolysis is to produce electro-nickel. The chemical composition and physical specifications of the electro-nickel produced in China have met the requirements of the national standard GB/T6516-97, as shown in Table 1.
2) anode mud during anodic electrolysis nickel sulfide, nickel-containing anode plate, copper, iron, and cobalt into solution most of him, and elemental sulfur and undissolved sulfide is formed and the noble metal anode mud. The anode mud rate of nickel sulfide electrolysis in China is about 25% to 30%, the anode mud contains about 80% sulfur, and the nickel content is about 4%. After the anode mud is washed with water to recover the free metal, it is used as a raw material for extracting precious metals and producing sulfur. Table 2 shows examples of anode mud rate and anode mud chemical composition.
3) The anolyte purified electrolyte enters the anode region through the diaphragm bag and becomes an anolyte. The content of H + ions and impurity ions in the anolyte is greatly increased by the influence of the anode reaction. The anolyte continuously flows out of the electrolytic cell, and is sent to purify and remove impurities to produce a new electrolytic solution.
2. The main technical and economic indicators of nickel sulfide electrolytic refining Nickel sulfide electrolytic refining is the process of converting the applied electric energy into chemical energy to obtain pure metallurgical products on the cathode. Therefore, the current efficiency, the trough voltage, and the electric energy consumption must be carefully examined in production. The main technical and economic indicators that are strictly controlled.